Home > Manufacturers > AWR Racing > Suspension >

AWR Rear Adjustable Sway Bar End Links: MAZDASPEED 3 & Mazda3
AWR Rear Adjustable Sway Bar Endlinks: MAZDASPEED3 and Mazda 3
AWR Rear Adjustable Sway Bar Endlinks: MAZDASPEED3 and Mazda 3
 
Our Price: $114.00



Product Code: AWR-4505R-M3
Qty:

Description
 
AWR Rear Adjustable Sway Bar End Link Set: MAZDASPEED 3 & Mazda3
 

Adjustable rear end links with heim jointed ends. Shown in picture below stock one with ball jointed end. Eliminates binding. Lets your sway bar do its job. Fits Mazda3 and Mazdaspeed3. Price is per pair.

Average Customer Review: Average Customer Review: 1.5 of 5 1.5 of 5 Total Reviews: 5 Write a review.

  0 of 0 people found the following review helpful:
 
1 of 5 Would give it 0 stars if it was an option November 19, 2011
Reviewer: drew from San marcos  
These are terrible and expensive to boot. I also experienced the same horrible clunking around 3-4 weeks after install; noticed it more on uneven road surfaces. eventually the passengers side endlink ceased to clunk but this was only because the bearing had snapped away from the housing. only lasted 3-4 annoying months, waste of money go with tri point's rear bar and links

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
1 of 5 needs to be redisgned August 28, 2010
Reviewer: firas khalif from san leandro , CA United States  
hi there. i bought these end link several months ago.and make clunking noise. i added steel sleeve to the hole of the sway bar and helped..but now its clunking again.... street unit guys i hope your paying attention because i paid 85 bucks for this thing and im not gonna dish out any more money to get it replaced..awr needs toget back to engineering better ones

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
1 of 5 Dont really work April 19, 2010
Reviewer: Peter from Vancouver, BC Canada  
They dont really work too well, they dont have a whole lot of play on them. They come loose after each day i drive them, i ended up having to put a couple of lock washers on them. They are making a lot of clunking noise when i go over uneven ground. And finally..

the ones i received do not match the ones in the picture... so ya... not recomended

Was this review helpful to you?

  4 of 4 people found the following review helpful:
 
1 of 5 Ummm...they don't fit on my Mazdaspeed 3??? May 27, 2009
Reviewer: Gabe from Honolulu, HI United States  
Tried to install on my Mazdaspeed 3 the lugs on these are about 1-2mm SMALLER than the stock ones.  I pre-fit them on the stock sway bar and they don't even fit those!! Theres so much "slop" in the hole with these you probably have to find custom fit sleeves as one review mentioned.  And that'll cost you even more $$$, but why bother??
Sreet Unit, this needs a fix or add a sleeve kit or something.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
4 of 5 Great Endlinks October 31, 2008
Reviewer: Matthijs Kettenis from Seattle, WA United States  
Great adjustability! I used them on Cobb stage 2 suspension kit.
Unfortunately bolts are much smaller than stock bolts, so be prepared to pay another 100 bucks on steel sleeves. There goes one star...
The stock end links did not allow me to use the stiffest position on the sway bars, with these its no problem.

Was this review helpful to you?